Dimensions of ASME B18.6.3 Type 2 Cross Recessed Flat Countersunk Head Machine Screws

Nominal Size or Baic Screw Diameter	Length, L	Head Diameter, A		Head Height, H, Ref.	Recess Diameter, M, Ref.	Recess Depth, T, Ref.	Recess Width, N, Ref.	Driver Size	Recess Penetration Gaging Depth		Protrusion Above Gaging Diameter, F		Gaging Diameter, G
		Max	Min						Max	Min	Max	Min
0	1/8	0.112	0.096	0.035	0.078	0.036	0.021	--	Note 6	Note 6	0.026	0.016	0.078
1	1/8	0.137	0.120	0.043	0.092	0.048	0.024	--	Note 6	Note 6	0.028	0.016	0.101
2	1/8	0.162	0.144	0.051	0.114	0.060	0.027	--	0.040	0.029	0.029	0.017	0.124
3	1/8	0.187	0.167	0.059	0.133	0.072	0.030	--	0.053	0.041	0.031	0.018	0.148
4	3/16	0.212	0.191	0.067	0.151	0.082	0.032	--	0.064	0.052	0.032	0.019	0.172
5	3/16	0.237	0.215	0.075	0.169	0.094	0.035	--	0.077	0.064	0.034	0.020	0.196
6	3/16	0.262	0.238	0.083	0.188	0.106	0.038	--	0.089	0.075	0.036	0.021	0.220
8	1/4	0.312	0.285	0.100	0.224	0.124	0.043	--	0.113	0.099	0.039	0.023	0.267
10	5/16	0.362	0.333	0.116	0.260	0.148	0.048	--	0.137	0.122	0.042	0.025	0.313
12	3/8	0.412	0.380	0.132	0.297	0.172	0.054	--	0.162	0.145	0.045	0.027	0.362
1/4	7/16	0.477	0.442	0.153	0.344	0.195	0.061	--	0.193	0.176	0.050	0.029	0.424
5/16	1/2	0.597	0.556	0.191	0.432	0.252	0.074	--	0.251	0.232	0.057	0.034	0.539
3/8	9/16	0.717	0.670	0.230	0.509	0.302	0.086	--	0.303	0.281	0.065	0.039	0.653
7/16	5/8	0.760	0.715	0.223	0.554	0.332	0.092	--	0.332	0.310	0.073	0.044	0.690
1/2	3/4	0.815	0.765	0.223	0.593	0.358	0.098	--	0.359	0.335	0.081	0.049	0.739
9/16	--	0.932	0.878	0.260	0.640	0.387	0.104	--	0.389	0.364	0.089	0.053	0.851
5/8	--	1.050	0.990	0.298	0.640	0.387	0.104	--	0.389	0.364	0.097	0.058	0.962
3/4	--	1.285	1.215	0.372	0.640	0.387	0.104	--	0.389	0.364	0.112	0.067	1.186

Note :

• Where specifying nominal size in decimals, zeros preceding the decimals and in the fourth decimal place shall be omitted.
• Screws of these length and shorter shall have undercut heads.
• Tabulated values determined from formula for maximum H in Appendix A.
• Point same on all drivers.
• No tolerance for gaging diameter is given. If the gaging diameter of the gage used differs from tabulated value, the protrusion will be affected accordingly and the proper protusion values must be recalculated using the formulas.
• Not practical to gage.